WHEATON Glass Warehouse
a division of WHEATON Industries Inc.
1000 N 10th St.
Millville, NJ 08332-2093
800.833.0410
856.825.9014 (F)
please contact: Bill.Dempsey@Wheaton.com
Length
The standard length is:
| + 10 mm | ||
| for Tubing |
1500
|
- 0 mm + |
| for Capillary and Rod |
1500
|
+/- 30 mm |
| for Tubing for Water Level Indicators |
2000
|
+10 mm |
| - 0 mm |
Special lengths of tubing, ranging from 1000 mm to 7500 mm, are available on request depending on the outside diameter.
Out-of-Round
Out-of-Round according
to ISO 1101 is dependent on the Outside Diameter (OD). The following maximum
values have been laid down:
| Tubing | |
| OD < 200 mm | tmaX 0.7 % of nominal OD |
| OD 2 200 - 325 mm | tmaX 1.0 % of nominal OD |
| Capillary | |
| OD < 10 mm | tmaX 1.0 % of nominal OD |
| Rod | |
| OD < 20mm | tmaX 1.0 % of nominal OD |
| OD ³20 - 30 mm | tmaX 1.0 % of nominal OD |
Siding
Siding greater than 12% of the nominal Wall Thickness within one cross
section is not permitted.
Straightness
Values for Straightness according to ISO 1101 are as follows:
| OD 3 - <6mm | max. 4.0 mm / 1500 mm |
| OD 2 ³ - < 30 mm | max.1.5 mm / 1000 mm . |
| OD ³ 30 - < 100 mm | max. 2.0 mm / 1400 mm max |
| OD ³ 100 - < 200 mm | 2.5 mm / 1400 mm |
| OD ³ 200 mm | max. 3.0 mm / 1400 mm |
Stress
|
WT<2
mm
|
WT2-4
mm
|
WT>4
mm
|
|
| Longitudinal Stress (M Pa) |
3.0
|
2.0
|
2.5
|
| Edge Stress (M Pa) |
4.0
|
3.0
|
1.5
|
0D = Ouside Diameter WT = Wall Thickness
Stones Diameter
| Stones Diameter |
Stones/kg
glass
|
| OD < 0.3 mm |
permitted
|
| OD ³ 0.3 - <1.0mm |
max.
2
|
| OD ³ 1.0 - <2.0mm |
max.
1
|
| OD > 2.0 mm |
not permitted
|
| Knots |
Knots/kg glass
|
| OD < 0.3 mm |
permitted
|
| OD ³ 0.3 - <1.0mm |
max.
4
|
| OD ³ 1.0 - <3.0mm |
max.
2
|
| OD > 3.0 mm |
not permitted
|
Length
The aggregate airline length
is the sum of all airlines ³ 20 mm length.
The permitted aggregate airline length is 0.8 m/10 m tubing.
Airlines < 20 mm (seeds): max. 20/kg glass
Width
Airlines wider than 1.0 mm
are not permitted for OD ² 100 mm.
Airlines wider than 2.0 mm are not permitted for OD ³ 100 mm.
| Tubing | End Finish | Square-Cut |
| OD 3-5mm | untreated | |
| OD 6-38 mm | plain cut and fused* | max. 2.5 mm |
| OD40-60mm | ||
| WT ² 3.2 mm | plain cut and fused | max. 2.5 mm |
| WT > 3.2 mm | plain cut | max. 3.5 mm |
| OD 65 - 325 mm | plain cut and fused* | |
| OD 65 - 100 mm | max. 3.0 mm | |
| (except WT > 9.0 mm) | OD 100 - 200 mm | max. 4.0 mm |
| OD> 200 mm | max. 5.0 mm |
*End finish when fused: bead thickness = approx. 0.1 mm (normal seal)
Capillary
Fused
Rod
Untreated
Special end finishes
on request.
Standard: Cartons
For Questions or to Submit Specifications for a Quote
Call: 1-800-833-0410 or e-mail at: Bill.Dempsey@Wheaton.com
|
|
* Note on Custom Design. Click on link to submit specifications for a quote over the Internet. Please note this will redirect you to the Wheaton Packaging website. To get back to this page, please use your browsers back button after submitting your information.